Related Products
Products you may like
3-Step Stop Rust System
Gloss Black
Semi-Gloss Black
Silver
Gray
Clear
Instructions
Warning
The POR-15 3-Step Stop Rust System is designed to stop rust on metal surfaces and ensures the best results when applying POR-15 Rust Preventive Coating. Prepare and prime bare metal or directly paint surface rust with confidence. The clear-cut process when using this rust stopper for metal allows for the proper cleaning, prepping, and coating of metal to create a non-porous surface to seal and protect metal from water, chemicals, salt, fertilizer, acids, alkalis, and other corrosive contaminants. Black and Gray Rust Preventive Coatings are non-conductive and good for EV conversion applications. A topcoat is required if exposed to UV light. Check out this rust stop undercoating now!

Step 1: POR-15 Cleaner Degreaser (Formerly Marine Clean) removes grease, oil, dirt, and grime in one application without leaving residues, noxious fumes, or flammable solvents. All in an easy to use water dilutable formula.

Step 2: POR-15 Metal Prep (Formerly Prep & Ready) etches and neutralizes the surface to provide the best adhesion for POR-15 Rust Preventive Coating, primers, and opaque DTM paint, on metal surfaces.

Step 3: POR-15 Rust Preventive Coating is a high-tech, high-performance rust preventive coating designed for application directly on stable rust or seasoned metal surfaces. Permanent rust protection with a hammer-tough finish resistant to acids, alkalis, oils, and repels all fuels.
Before: Heavily rusted diamond-plate pickup truck beds can be a problem, fix them permanently with the POR-15 3-Step System.
Step 1: Clean it! Remove loose rust and grime; Soak surface with a water-based Cleaner Degreaser and breakup the grease and oil. Rinse with water and let dry.
Step 2: Prep it! Neutralize rust and etch with Metal Prep. Soak surface and keep it wet for 20-45 minutes. Rinse with water and let completely dry.
Step 3: Coat it! After thorough washing and drying, coat with POR-15 Rust Preventive Coating, right onto the surface rust! At least two thin coats for normal applications.
For areas exposed to U.V. light: Topcoat with Top Coat, 2K Industrial Urethane, or other UV safe opaque paint of your choice.
After: Now you have a PERMANENTLY repaired truck bed, that won't rust again.
ASTM C-580 Flexural Strength - measures flexural strength and modulus of elasticity. 5,200 pounds per square inch
ASTM C-579 Compressive Strength - measures compressive strength, the capacity of axially directed pushing forces. 12,500 pounds per square inch - Verified. Not tested to failure.
ASTM C-307 Tensile Strength - measures the tensile strength of cured chemical-resistant materials. 3,200 pounds per square inch
ASTM D-4541 Bond Strength To Concrete - measures the strength of coatings bond to concrete. Concrete fails before POR-15 Rust Preventive Coating. It exceeds the tensile strength of concrete
ASTM C-501 Taber Abraser - abrasive wear by determination of the loss of weight resulting from abrasion. In two separate tests, POR-15 Rust Preventive had:
Weatherometer - accurate weather resistance indicator of cycling of conditions. The cycle is 30 mins at 135 degrees F, 30% relative humidity and 30 mins at 75-80 degrees F, 100% relative humidity 1,000 hours of exposure equals 5 years of simulated exposure in the Rocky Mountain region. There was no change in the 3 panels coated with POR-15 Rust Preventive Coating exposed for 2,000 hours.
ASTM B-117 Salt Spray - specimens exposed at specific locations and angles. Created a 100% relative humidity condition in the exposure zone.Two separate B-117 tests. One with new bare steel and the other with rusted steel. Both were coated with POR-15 Rust Preventive Coating.
Chemical Bath Test - After 200 hours of soaking in the following chemical bathes, panels coated with POR-15 Rust Preventive Coating experienced no changes: 10% hydrochloric acid, 50% sulphuric acid, 55% chromate, 85% phosphoric acid, 10% sodium hydroxide 98% methanol.
Raw Sewage Test - A metal box that houses a filter for raw sewage in a treatment facility was coated with POR-15 Rust Preventive. After a year of service, no undercutting or rusting was present on the housing.
Mil-D-3134J Impact Resistance - POR-15 Rust Preventive Coating exceeds standards.
ASTM C-413 Water Absorption - method covers the determination of absorption of chemical-resistant mortars, grouts, monolithic surfacings, and polymer concretes. 0.0001 maximum
NACE Stand TM0174 - 0.00 POR-15 Rust Preventive Coating is a non-porous coating.
Temperature Resistance - POR-15 Rust Preventive Coating is temperature resistant up to 450° continuously. Test showed no adhesion lost at 450° F for 10 hours.
Floor paint always scuffed off to metal. Finally tried POR15, looks the same now as it did eight ago when applied.
Trying something new with it! Lawn tractor mowing deck is bare metal from mowing. Was preparing to coat it with paint and remembered i had some POR15 left. Finished coating the devk and replaced blades. CAN NOT WAIT TO SEE HOW IT HOLDS UP TO SANDBLASTING OF LAWN i next fall!
POR15 Cures from atmosphere, air and moisture. Keep the lid on as much as possible,
pour POR15 into a paper cup and put the lid over the can to only allow minimum exposure to atmosphere.
When you are done painting, use a plastic sheet over the can then close with the can top.
PUT the can in a plastic bag and store the can UPSIDE DOWN. Keeping in a tray
would be a good idea in case some of the POR15 leaks out.
I used this on my 2002 Chevy Silverado 1500 Extended Cab. I live in New England, so major rust issues. Removed the bed, gas tank, leaf springs, and shocks; Followed the instructions. See the before and after pictures. Amazing results. very happy with the product; next summer I will take the cab off and restore the front of the truck!
Removed rust from my boat trailer axes and used all three products. Easy to use just follow directions. Drying time depends on weather. I gave my trailer axe two coats. Easy to apply with a brush. Make sure you have adequate ventilation. Tailer looks better than new with a Hard Shinny Coat.
love how it evens itself out, really nice gloss finish
Metal that is near white rough media blasted provides the best surface for coatings. If not possible, remove all built-up dirt, loose rust, and paint. Note that if you leave old paint behind, the rust preventive can only adhere as strongly as the paint it is applied over. This generally is not as strong as applying to prepped and scuffed-up bare metal. For new metal or smooth surfaces, roughen with 100-180 grit pad/paper.
These products should only be handled when wearing latex gloves, eye protection, and NOSHA approved respirator. Always work in a well-ventilated area.
Step 1. Apply our POR-15 Cleaner Degreaser to a surface, keep wet 10-15 minutes and agitate the surface with a scuff pad or stiff brush to break up oil and grease. Then rinse thoroughly with clean water and allow the surface to dry. Repeat if surface is still oily or greasy. It is important Not to allow the product to dry on the surface while working or prior to rinsing with water. POR-15 Cleaner Degreaser can be diluted 4:1 for normal degreasing or up to 10:1 for second round degreasing with warm water. POR-15 Cleaner Degreaser is a heavy duty water soluble cleaner that may be used over metal, wood, fiberglass, vinyl, and concrete.
Step 2. Apply POR-15 Metal Prep to the bare metal surface, keep wet with Metal Prep for 15-25 minutes for normal use and 25-45 minutes for heavy rust and new metal, then rinse thoroughly with clean water and allow the surface to dry completely. Once dry the surface may show a flash rust or white powdery residue this is perfectly normal. POR-15 Metal Prep provides the best surface profile and greatly improves paint adhesion to any type of metal surface for opaque paints and coatings.
Step 3. Wearing gloves, eye/face protection, and a properly fitted NIOSH approved respirator is recommended when applying POR-15 Rust Preventive Coating. Surface must be clean and completely dry. Do Not shake. Mix by stirring until all solids at the bottom of the can are dissolved. Mixing may be done with a drill mixer on slow to medium speed or by hand. It is recommended to apply two thin covering coats of POR-15 Rust Preventive Coating. Three thin coats may be needed for extreme industrial and marine applications. Apply the first coat to the properly prepared substrate with a brush, roller, or HVLP (proper PPE required). Apply the second coat when the first coat is dry but still slightly tacky to the touch. If POR-15 Rust Preventive Coating is applied too heavy, brush marks or bubbles may result in the finish. Do not apply this product if the humidity is above 75%. If the humidity is too high POR-15 Rust Preventive Coating will surface dry too quickly which may result in small bubbles in the finish. POR-15 Rust Preventive Coating requires an UV safe opaque topcoat only if exposed to direct sunlight. Best chemical adhesion to POR-15 Rust Preventive is when it is dry but still tacky (it has a finger drag). If the rust preventive is already completely dried or cured, you must wait 24 hours and gently scuff the surface with a maroon pad or 280-320 grit sandpaper for mechanical adhesion of a second coat or a topcoat.
If your project will be exposed to U.V. light, topcoat it with an opaque POR-15 TopCoat, Engine Enamel, Caliper Paint, Detail Paint, or 2K Urethane industrial topcoat. You can topcoat with most other UV safe opaque paint as well.
Semi-Gloss Black
WARNING: This product can expose you to chemicals including Carbon Black and Cumene which are known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
Gloss Black
WARNING: This product can expose you to chemicals including Acetaldehyde, Propylene oxide, Carbon Black, and Cumene which are known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
Silver
WARNING: This product can expose you to chemicals including Cumene which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
Gray
WARNING: This product can expose you to chemicals including Titanium Dioxide, Carbon Black, Ethyl Benzene and Cumene, which are known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
Clear
WARNING: This product can expose you to chemicals including Cumene, which are known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
Products you may like
Your Browsing History
Floor paint always scuffed off to metal. Finally tried POR15, looks the same now as it did eight ago when applied.
Trying something new with it! Lawn tractor mowing deck is bare metal from mowing. Was preparing to coat it with paint and remembered i had some POR15 left. Finished coating the devk and replaced blades. CAN NOT WAIT TO SEE HOW IT HOLDS UP TO SANDBLASTING OF LAWN i next fall!
POR15 Cures from atmosphere, air and moisture. Keep the lid on as much as possible,
pour POR15 into a paper cup and put the lid over the can to only allow minimum exposure to atmosphere.
When you are done painting, use a plastic sheet over the can then close with the can top.
PUT the can in a plastic bag and store the can UPSIDE DOWN. Keeping in a tray
would be a good idea in case some of the POR15 leaks out.
I used this on my 2002 Chevy Silverado 1500 Extended Cab. I live in New England, so major rust issues. Removed the bed, gas tank, leaf springs, and shocks; Followed the instructions. See the before and after pictures. Amazing results. very happy with the product; next summer I will take the cab off and restore the front of the truck!
Removed rust from my boat trailer axes and used all three products. Easy to use just follow directions. Drying time depends on weather. I gave my trailer axe two coats. Easy to apply with a brush. Make sure you have adequate ventilation. Tailer looks better than new with a Hard Shinny Coat.
love how it evens itself out, really nice gloss finish
I used this on my 2002 Chevy Silverado 1500 Extended Cab. I live in New England, so major rust issues. Removed the bed, gas tank, leaf springs, and shocks; Followed the instructions. See the before and after pictures. Amazing results. very happy with the product; next summer I will take the cab off and restore the front of the truck!
In order to open my pint can of paint,I used a typical paint can opener. Everywhere I pried, the lid edge just peeled up. I finally had to use a small pair of channellock pliers to get the can open. Naturally this destroyed the lid. I'm sure the remaining paint will harden before I can use it. At $47 a pint I'll be throwing about $23 in the garbage. If you are going to charge premium prices for your product, put it in something better than a 2 cent can! I cannot speak for the product quality, as this is the first time that I have used it. The product I was using is Rust Preventive.
In order to open my pint can of paint, I had to destroy the lid.I used a typical paint can opener, and pried along the edge as usual, which caused the edge to peel at every point I pried. I finally had to use a small set of channellock pliers to open the can. Naturally the lid is ruined, and the remaining paint will harden before use. I used about 1/2 of the pint. At $47 a pint, this is a lot of money to toss in the garbage. If you are going to charge premium price for your product, please spend more than 2 cents for the can! I cannot speak on the quality of their product, as this is the first time that I have used it.
Hi Bob, we’re sorry the can was so difficult to open.. We understand how frustrating that is, especially at this price. Please contact our customer service team with your order details so we can look into this and help. This is not due to the can being low quality. It is due to the strength of the Rust Preventive coating. Once the rust preventive cures to metal it is very difficult to remove. This unfortunately can happen if a drop touches the rim or seal during production and results in a lid that can't be removed.
Contact support@POR-15.com with your order number and a photo.
Followed the instructions as humanly possible and within 20 minutes it dried up and when I rolled the tank, it came apart and clumps. If I can figure out how I will add pictures to this review just like that wasted $100.
Never received my paint just the cleaner and preparation and no one has answered my question where is it
Floor paint always scuffed off to metal. Finally tried POR15, looks the same now as it did eight ago when applied.
Trying something new with it! Lawn tractor mowing deck is bare metal from mowing. Was preparing to coat it with paint and remembered i had some POR15 left. Finished coating the devk and replaced blades. CAN NOT WAIT TO SEE HOW IT HOLDS UP TO SANDBLASTING OF LAWN i next fall!
Firstly, this stuff works great. I've used it a few times and it always leaves a good, durable coating.
But there are some precautions that I'd recommend. Get a top that seals with a poor spot and stirrer for the paint. You don't want to leave the paint exposed or you can lose your whole supply. Pour it into a cup and use that to paint with.
Next. I'd suggest latex gloves when brushing this stuff on. I don't know how it happens, but even being careful, you are going to get paint on you. And for some reason, this paint absolutely refuses to come off your hands. The can says 2-6 hours dry time, but I swear this stuff will dry on your hand within 60 seconds. And it is nearly impossible to get it off.
POR15 Cures from atmosphere, air and moisture. Keep the lid on as much as possible,
pour POR15 into a paper cup and put the lid over the can to only allow minimum exposure to atmosphere.
When you are done painting, use a plastic sheet over the can then close with the can top.
PUT the can in a plastic bag and store the can UPSIDE DOWN. Keeping in a tray
would be a good idea in case some of the POR15 leaks out.
Removed rust from my boat trailer axes and used all three products. Easy to use just follow directions. Drying time depends on weather. I gave my trailer axe two coats. Easy to apply with a brush. Make sure you have adequate ventilation. Tailer looks better than new with a Hard Shinny Coat.
love how it evens itself out, really nice gloss finish
I have used Por15 on a lot of projects. VERY TOUGH Layer after cured. It is affected by UV
and if not protected will wear off in a few years time if you do not coat it with a Top Coat Paint.
HUGE WARNING, Don't get POR15 on any moveable parts, hinges, or bolts that you may want
to remove later.
Once POR15 cures, it will lock any seams, bolts, nuts into basically ONE WHOLE PIECE.
MAKE SURE the surface is clean, Grease and Oil free. Use the cleaners.
POR15 goes on like a very fluid paint, IT WILL RUN if you apply too much at once so
be watchful. Be cautious as you can't brush POR15 too much during the dry period as
it begins to skim over, brushing will mess it up. Any voids, seams spaces between
moving parts WILL BE SEALED AS ONE SOLID PIECE. fair warning.
I am always using POR15 for some project to prevent rust or to stop rust. You can
just open the can and use a little if you store it carefully.
-- FOR STORAGE --
POR15 Cures from atmosphere, air and moisture. Keep the lid on as much as possible,
pour POR15 into a paper cup and put the lid over the can to only allow minimum exposure to atmosphere.
When you are done painting, use a plastic sheet over the can then close with the can top.
PUT the can in a plastic bag and store the can UPSIDE DOWN. Keeping in a tray
would be a good idea in case some of the POR15 leaks out.
The POR15 in the can WILL SKIM OVER on the top, the side with the Air inside.
IF you store a used POR15 can Top side UP, the top of the POR15 WILL skim
over. If the skim layer is not too thick, you can break it and access the product
under the skim layer. Better Idea to store the can upside down and let the
skim layer form on the bottom side of the can.
The POR15 should be usable when you open it again, unless you allowed long term exposure
to the atmosphere when you were using it. If the POR15 had a long term exposure to the
atmosphere, then it may cure completely in the can no matter what.
WHEN USING, wear old clothes and gloves.
POR15 on skin is difficult to get off and you may end up wearing it off. Try kerosene on a
paper towel to get most of it off the skin.
You CAN NOT get POR15 off of clothes or concrete and it will take literally YEARS for the
POR15 to wear off of CONCRETE.
Used this for the first time on my 1964 Dodge Polara floor pan. Works amazing. The floor is pretty much bullet proof now! And looks amazing!
Covers well with only a brush looks great will def be using again !!!!!
I am very impressed with every product that I’ve used from POR-15 to restore my very rusty truck. I have the first and worst half of the truck frame all restored and it’s looking amazing. Just follow their directions and you get a extremely durable new paint finish. It is holding up great to the bangs and bumps of installing all the newly repainted parts to the repainted frame. Couldn’t be more pleased with their products.
I'm not sure how it works but followed the directions and sprayed it no peeling or orange peel so far (1mth)
Looks really good , sprayed it with a gun got no over spray
I did it myself and it came out beautiful
Preperation s key with POR 15 products. Do the prep work and the results are amazing durability and ease of application. Superior product.
First time using POR15 products and am more than pleased with the outcome. Coated the complete bottom side of my newly acquired rust free California truck and it came out great. Gloss black finish is hard as a rock and hopefully will, with proper care and undercarriage washing, keep the rust off of my forever truck. Some coating leached through my water resistant tyvek suit and it was a bit challenging removing the paint from my forearm. Was able to soak it with olive oil and used my wife's mild exfoliant and after careful scrubbing was able to be paint free.
Love the finish on the truck and will use againas needed. Highly recommend as it is a really great product. Follow the directions.
Thanks POR15 company for such a great product.
Product arrive in good condition. It was exactly what I had ordered. Have not been able to use it yet cause we have been running 70-95% humidity, so waiting for Mother Nature to get happy again. Only reason for four stars and not five is due to not being able to put any on
Degreased it, Acid etched it, Painted it. The paint went on so effortlessly and came out so amazing. Leveled out like glass. Two days later lifted the 800lb 1/2 inch plate metal workbench with straps and it left no marks in the paint. Crazy tuff. Only thing I would do different is remove more of the grease and oil before using the degreaser. Several of the pits in the metal still had oil or grease in them and fisheyed. My fault.
This product is the best self-leveling stuff i have ever used. My truck frame looks just incredible!
I am the owner of a 1989 Dodge W100. She's a Northern truck, so the road salt has done it's damage. I have tried many rust preventatives, encapsulators, etc ... None seemed to really do the work that POR15 has. I followed the directions and I am VERY impressed with the results. So impressed in fact, that I now plan to do the underside of the bed.
We have been using these products in our shop for over 20 years. Consistent results that literally last forever.
I have used this product multiple times and rather than destroy the can trying to open it, we just put a 2 holes in the lid. One to pour the POR15 from and the other to act as a vent, then when finished a piece of aluminum tape over each hole and it's good to go.
My son-in-law recommended the Por15 products for rust removal. I am the lady of the house. I ordered the three step permanent rust removal system. I followed the directions exactly and wore the personal protective equipment, in a very well ventilated area. I treated the camper hitch, bumper, and all the metal framework under the camper. I used a leaf blower on the metal to make sure the surfaces were bone dry before painting. The job used nearly all the pint of paint. The next day I noticed a three foot section that I had missed. The can was very difficult to reopen (I hadn�t read the tip about using plastic wrap). The leftover paint was starting to set up; but I was able to stir it up and get what I needed to finish the section that I missed. I had accidentally gotten some paint on my forearm when my sleeve moved. I�m not sure how to get this paint off skin. I tried four different methods to remove the paint, and nothing seems to work. Permanent! It did the job on the metal (gorgeous)! On the skin, it is wearing off. I am pleased.
Used this on lolly support columns in a crawl space that occasionally gets wet after big rain storms. They were starting to rust where the water touched them. I dug around footers scraped and used the Stop Rust System, and then re-cemented the holes. I had water in the crawl space and it flooded twice during a remodel after I finished. No bleed through at all. It didn't even get scratched when re-applying the rock back fill and cement. Amazing primer system! I wish the steel manufacturers used this at the factories. FYI took a tip from other users and used the Dry time accelerator and mixed in a different can to speed things up, and put plastic saran wrap between the lid and the original can to prevent the top from getting glued to the can between uses.
I have great expectations for POR-15 and have several vehicles, including a large flatbed trailer, to use it on. I am reluctant to open the POR-15 paint can due to all the warnings of never getting the can open again and the humidity turning it solid. I did buy 30 ML syringes to carefully transfer liquid and still deciding if I want to split the liquid into separate containers and even add some CO2 or nitrogen to the top due to the humidity where I live.