Related Products
Products you may like
Self Etch PrimerStock Adequate!Ready to ship
Instructions
Warning
With the POR-15 Self Etch Primer spray can, you can even topcoat POR-15 Rust Preventive Coating that's been in place for months or years.
POR-15 Self Etch Primer is NOT a high-build primer like POR-15 High Build Primer, but it can be sprayed on almost any painted surface and can be top coated in 20 - 30 minutes. It bonds incredibly well to POR-15 Rust Preventive Coating, and all topcoats bond incredibly well to POR-15 Self Etch Primer. It can be sanded lightly, and if desired, multiple coats may be applied.
Use over a light coating over the POR-15 Rust Preventive Coating when it is dry to the touch but still tacky (has a finger drag) for top coating later finishing. In situations where you are topcoating a very old POR-15 Rust Preventive Coating, we first recommend a light sanding with any 280 to 320 grit paper, clean it, and use POR-15 Self Etch Primer.
This self-etching primer spray paint for metal replaces Tie Coat Primer.
POR-15 Self Etch Primer Technical Data Sheet
Works great for my needs…
Self Etch Primer
Self Etch Primer
Really does adhere well. POR is a go to product for me.
Self Etch Primer
For maximum adhesion sand surfaces to be painted with 180-320 grit sandpaper. All surfaces must be clean and free of all dirt, loose rust, oil, grease, wax, soap, loose paint and any other matter. Clean painted and bare metal surfaces with POR-15 Cleaner Degreaser. Metal surfaces should be treated with POR-15 Metal Prep for maximum adhesion.
Previously Painted Areas: Scuff surface with 280-320 grit sand paper. Use POR-15 Cleaner Degreaser and POR-15 Metal Prep. Let surface dry thoroughly.
Bare Steel or Aluminum: Clean and prep surface then let dry thoroughly. For best corrosion protection, apply the POR-15 Rust Preventive as an undercoating primer. Self Etch Primer can be applied over the Rust Preventive when it is dry to the touch, but still slightly tacky (has a finger drag).
Shake can well before spraying. Keep can 8-12 inches from surface as you paint. Spray two light coats of POR-15 Self Etch Primer and allow 10 to 20 minutes between coats. POR-15 Self Etch Primer can be topcoated in 30 minutes. It is not necessary to sand POR-15 Self Etch Primer before top coating.
Dry time: It cures to touch in 30-60 minutes. Second coat can be applied in 10-20 minutes, depending on ambient temperature and humidity.
Cleanup: To prevent clogs in spray nozzle, hold can upside down and spray until clear gas appears.
Empty aerosol cans are recyclable or may be discarded in regular trash pick-up. Do not incinerate or compact.
WARNING: Cancer - www.P65Warnings.ca.gov.
Products you may like
Your Browsing History
Works great for my needs…
Self Etch Primer
Self Etch Primer
Really does adhere well. POR is a go to product for me.
Self Etch Primer
Works great for my needs…
Self Etch Primer
Self Etch Primer
Really does adhere well. POR is a go to product for me.
Self Etch Primer
I love this stuff , I've been using fortune plus years. Can always count on the quality.
Do not use in conjunction with POR-15 Rust Preventive Coating. It says it will bond in their website description but I soon found out after wasting $1,500 of labor that it the POR-15 Rust Preventative Coating does not stick to it. I also called their tech support and they told me not to use it with the POR-15 brush on Rust Preventative Coating. I am not sure why there website description says it does. This information would have saved me money and time. I wasted 5 cans of primer and 1 quart of undercoating along with $1,500 of POR-15 Rust Preventative coating. The website should be changed hopefully this review will save people time and money.
Sorry for the confusion. It sounds like you may have applied it out of order. The stop rust system 'Rust Preventive' is a direct-to-metal product. The Rust Preventive should be applied first right on the cleaned roughened metal. When it is dry but still tackey you would use the Self Etch Prime over it. It sounds like you applied the Self etch first and it completely dried so the Rust Preventive didn't adhere properly. Technically you could scuff the self-etch primer with 180-240 grit and the Rust Preventive would adhere, but it isn't the recommended application. We will try to clarify this on the site. Sorry for the confusion on the application.
I HAVE USED THIS STUFF BEFORE, AND IT NEVER FAILS ME. IF YOU ARE RESTORING ANYTHING METAL, USE THIS.
Fantastic spray pattern and little pricey but it was great
Best primer I have ever used.
POR-15 works great on wire brushed surfaces with rust. Great product
I haven't had time yet to use this yet. Lots of irons in the fire and project car takes a back seat. I'm sure it will be great!
Relatively simple process and looks great when you’re done.
The spray nozzle on the spray can seemed to allow the primer to flow out of the can vey consistently, without any material buildup on the nozzle. Primer went on to item being coated in a consistent wet, non-dry spot manner. Able to apply even amount of material in hard to reach locations on item without invoking a material ‘run’ or ‘sag’. Primer was applied over a substrate surface that was mix of bare metal and 40 plus years old factory original coating, prepared using red Scotchbrite, and POR 15 Cleaner and Metal Prep products. Primer was ready for Topcoat in 30 minutes, as stated in directions, all of this coating activity being perform in the mid 60 degree temperatures. Topcoat went on well over the primer, with no lifting, wrinkling, sagging, runs, or any of the other myriad of paint imperfections that can occur. I definitely recommend this product.
Nice product works well
Utilized as part of truck bed liner application on a UTV with rusted bed floor. Stripped/wire brushed floor to bare metal and cleaned/prepped. Used self etch primer on sides (masked 4" up and lightly sanded only) as prior paint still in reasonable shape. 2 coats POR-15 on all then 2 coats bed liner on floor only. POR-15 so far appears very tightly adherent to primer on sides of bed, probably 20-30 mils minimum thick achieved. Bed liner on floor very good result. The self etch primer spray can did "spit" small globs occasionally, can't see any real effect after all said and done, pleased with overall result.
Very happy with all POR products except one. I used everything…. Cleaner/degreaser, metal prep, the rust preventative, self etch primer, and finally the top coat. Everything worked as described except the top coat. U can take your finger nail and scratch it off. It’s almost like it didn’t adhere to the primer. Outside of that I’m very happy.