High Temp

High Heat Resistant Paint

item(s): 44116

Size
Color

POR-15 High Temp Heat Resistant Paint

POR-15 High Temp Heat-Resistant Paint is capable of withstanding extreme temperatures up to 1200°F / 648.8°C and will resist cracking, chipping, and peeling. This high temperature coating is also extremely weather, salt, and moisture resistant. Our heat resistant paint is the most uniform heat-resistant coating available anywhere and will maintain rich, brilliant colors without burning off or discoloring. This heat-resistant spray paint can be used on all cars, domestic or foreign. Also, this high-heat coating meets or exceeds properties and requirements of MIL-C-13370.

Note: To reduce POR-15 High Temp paint when spraying with an HLVP system, use POR-15 Solvent. You can reduce up to 10% maximum. You can also use POR-15 Solvent for cleanup.

Replaces POR-20, Black Velvet, Fire Seal 2000, and Factory Manifold Gray


POR-15 High Temp Technical Data


Manifold painted with POR-15 High Temp paint
Manifold painted with POR-15 High Temp paint
From left to right: Aluminum, Manifold Gray, Flat Black

Liquid Paints

Flat Black
WARNING: Cancer - www.P65Warnings.ca.gov.

Manifold Gray
WARNING: Cancer - www.P65Warnings.ca.gov.

Aluminum
WARNING: Cancer - www.P65Warnings.ca.gov.

Aerosol Paints

Flat Black
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Manifold Gray
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Aluminum
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Customer Reviews

Based on 29 reviews
93%
(27)
3%
(1)
0%
(0)
0%
(0)
3%
(1)
S
Steve Edenfield

best i ever had

J
Jim Townsend
Super high temp

I use on Model A exhaust manifolds keeping them rust free.

J
Justin Childress
High Temp Coating

We only use Por15 at our business for turbos and headers. I've used other name brands that are very popular and had very bad results. Parts would begin to rust with in a year or less.
Por15 has lasted the longest and still counting with no customer complaints to us on chipping, fading or rusting. Our shop coats around 40 sets of headers and 20-30 turbos every year. A little bit goes a very long ways so follow the instructions and make sure your sandblaster is free of moisture when blasting and you will have the results your looking for. Applied Coatings & Gunworks

D
Dave Sheppard
500 Gallon Smoker

Just fired up the big 500 gallon smoker over the weekend and the paint held up with no problem. It even wipes clean and doesn't let grease soak in. No smoke build up or burn on the fire box door. Can't recommend it enough.

J
Joe Hybdzinski
Good Product

Coverage is great, its very smooth and spreads nicely, dries evenly

Read all safety warnings and precautions on label before use.

Application:

Liquid paint directions:

On previously painted surfaces blistered and loose paint must be removed. Sandblasting is the optimum surface preparation. Clean painted and bare metal surfaces with POR-15 Cleaner Degreaser to ensure that the surface is clean, dry, and free from oil, grease, dirt, salts, and any other contaminants. Paint  all bare areas with two coats of POR-15 High Temp Coating. Glossy surfaces should be roughened with 320 grit sand paper before recoating. Allow POR-15 High Temp Coating to cure for 24 hours on the surface before temperature is raised above 300°F for full cure.

Dry time: Cures to touch in 4 hours. Second coat can be applied in 24 hours, depending on ambient temperature and humidity. POR-15 High Temp reaches maximum hardness after heat exposure above 300°F (150°C) for 15 minutes and then allowed to cool down.

Clean up: Do not put left-over paint back into can. Clean all equipment immediately after use. At the same time, flush out all fluid lines and carefully clean pressure pots. Use clean POR-15 Solvent only. It is also good practice to periodically clean the spray tip or the fluid tip/air cap combination during the course of the working day or shift.

Aerosol spray directions:

Surface must be clean, dry an free of all oil and other contaminants before painting. Sandblasting is the optimum surface preparation. Protect surrounding areas from spray mist. Must be heat cured at a minimum temperature of 400°F (205°C) for two hours. More than one coat may be required for full hide.

  • Shake can at least one minute before and occasionally during use.
  • Spray surface with steady, even strokes at a distance of 8 to 10 inches. Several light coats give a better finish than one heavy coat. For best results, recoat within 1 hour or after 24.

Cleanup: To prevent clogs in spray nozzle, hold can upside down and spray until clear gas appears. Completely empty cans may be recycled or disposed of with regular trash. Dispose of partially empty cans responsibly. DO NOT puncture, incinerate or compact.